FR58L4HS-2020L

      FR58L4HS-2020L

      FR58L4HS-2020L is a high-performance 5.8G radar sensor FMCW ranging and presence sensing launched by Ferry Smart Intelligent. The radar module uses the Doppler principle to transmit high-frequency electromagnetic waves through the antenna and receive the initial reflected waves to judge the movement of objects within the coverage area and give corresponding electrical signals. Signal. Module size 20*20MM The chip integrates 5.8G microwave circuit, intermediate frequency amplifier circuit and signal processor, with high integration and good production consistency. The module has a built-in 32-bit MCU and a transceiver antenna, which greatly improves the sensing performance of the sensor.

      The radar module has a long sensing distance, a wide angle, no dead zone, and the lens and lens aging problems are not affected by temperature, humidity, airflow, dust, noise, brightness and darkness. Widely used in smart lighting, smart door locks, smart security, smart home appliances and other fields.

      Hardware Instructions

      2.png

      Device distribution diagram on the front and back of the module

      FR58L4HS-2020L hardware reserves 5pin connection pin header, the pin distance is 2.54mm

      The following is a detailed description of each PIN corner name, function, working range, etc.

      Pin pin

      Functional remarks

      remarks

      TXD

      Burning port tdio

      Compatible with UART TX and IO ports

      RXD

      Burning port TCLK

      Compatible with UART RX and IO ports

      OUT

      output signal

      The output signal is high and low level (0V / 5V)

      GND

      Grounding pin

      VCC

      Power supply module

      LDO is not attached by default, and the power supply voltage is (4.5 ~ 5.5V). If 12V power supply is required, LDO needs to be added, and the power supply VCC is 5V ~ 12V

      Technical Parameter

      parameter

      Small value

      Typical value

      Large value

      Company

      remarks

      Emission frequency

      5725

      5800

      5875

      MHz


      input voltage

      4.5

      5

      5.5

      V

      If 12V power supply is required, LDO shall be added

      Output high level


      5


      V


      Output low level


      0


      V


      Working current


      33


      mA


      Sensing distance

      0.1

      /

      70

      M

      The distance can be adjusted according to demand

      Delay Time


      2


      S

      Specific requirements are adjustable

      Photosensitive threshold


      N/A



      Optional, no photosensitive paste by default

      Antenna beam angle


      100


      °


      size


      20*20


      mm


      working temperature

      -30


      85


      Storage temperature

      -50


      125



      Description of packaging method

      The module is packaged in a blister box and placed in the blister box;

      1. Put the blister boxes into the carton according to the stack of 10 boxes;

      2. The air raid in the carton is filled with instant noodles to reduce transportation wear;

      3. Bubble film is placed on the bottom of the carton to prevent transportation wear;

      4. Cover the top layer with bubble wrap and seal with tape to prevent shaking.

      3.png

      Installation Precautions

      1. When installing the antenna, there should be no metal shells or components on the front of the antenna to avoid shielding the signal. Blocks such as plastic or glass are allowed, but the block should not be close to the front of the antenna;

      2. Try to avoid directing the radar antenna to large metal equipment or pipes, etc.;

      3. When installing multiple radar modules, try to ensure that the antennas of each radar module are parallel to each other, avoid direct irradiation between the antennas, and maintain a distance of more than 1m between modules;

      4. The radar sensor should avoid facing the AC drive power supply, and try to stay away from the rectifier bridge of the drive power supply to prevent the power frequency from interfering with the radar signal;

      5. It is recommended that the power supply driving capability of the radar module is not less than 50mA, otherwise it may cause the sensor to work

      6. When installing, ensure that the installation position of the sensor is firm and stable. The shaking of the radar itself will have a great impact on signal processing.

      7. When installing, make sure that there is no object movement or vibration on the back of the radar. Since the radar radio frequency wave is penetrating, the signal on the back of the antenna will also pass through the radar board. If there is an object moving on the back, it will also be collected by the antenna, which will affect the judgment effect. A radome or backplane can be used to reduce the effects of objects behind the radar.

      8. When installing, try to ensure that the radar antenna is facing the area to be detected, and the surrounding area of the antenna is open and unobstructed.

      成人无码精品1区2区3区免费看| 日韩一级黄色录像| 91精品手机国产免费| 亚洲精品无码鲁网中文电影| 精品视频午夜一区二区| 日韩精品无码永久免费网站| 久久精品无码一区二区三区不卡 | 精品小视频在线观看| 国产精品午夜无码av体验区| 国产精品99久久久久久宅男小说| 久久成人国产精品免费软件| 精品无码日韩一区二区三区不卡| 久久午夜精品视频| 国产精品乱码高清在线观看 | 91精品国产色综合久久不| 久久99精品久久久久久青青日本| 国产AV无码专区亚洲精品| 亚洲精品亚洲人成人网| 亚洲精品无码精品mV在线观看| 中文精品久久久久人妻| 国产午夜精品一区二区三区不卡| 国产精品乱码一区二区三区| 亚洲精品老司机在线观看| 午夜精品久久久久久久无码| 日韩成人精品日本亚洲| 日韩午夜在线视频不卡片| 日韩欧美一区二区三区免费观看| 精品日韩亚洲AV无码一区二区三区 | 亚洲精品第一国产综合精品| 一区二区三区日韩精品| 精品人人妻人人澡人人爽牛牛| 国产精品视频一区二区猎奇| 99re热免费精品视频观看| 99久久这里只精品国产免费| 一区二区亚洲精品精华液| 日韩中文字幕精品免费一区| 国产成人精品a视频一区| 日韩精品无码人妻一区二区三区| 日韩电影中文字幕在线观看| 日韩在线视频导航| 精品乱人伦一区二区|